IVECO Daily IV 2006-2011 Air Intake Duct 2.3 3.0 504139775 504345694 504193548
IVECO Daily IV 2006-2011 Air Intake Duct 2.3 3.0 504139775 504345694 504193548
IVECO Daily IV Air Intake Duct / Air Filter Intake Pipe
Used original factory-fit intake duct for documented Daily 35C / 35S / 50C / 65C applications. Match the part number and shape, then request a VIN check through eBay Messages before ordering.
Actual Item — Photos From This Listing
Where This Part Fits & What It Does
Function
This moulded plastic duct forms the front air-inlet route to the air-filter housing. Its job is to guide incoming air from the front intake area toward the filter box while keeping the intended factory routing and clearance around surrounding components.
Typical position: front of the vehicle / front engine-bay area, behind the front fascia or grille area and upstream of the air-filter housing.
What it controls: it does not electronically control the engine. It physically controls the route by which intake air reaches the air-filter housing.
Fitment Location Guide
This diagram is a location guide only — not a fastener map or substitute for VIN confirmation.
BEHIND FRONT FASCIA
A third-party vehicle photograph is intentionally not used in this eBay-safe version. The diagram prevents a stock/reference vehicle image being mistaken for the vehicle the used part came from.
Verified Compatibility Chart — Part-Number Evidence
The following applications are documented against the 504139775 / 504193548 / 504345694 part-number family. VIN confirmation remains the final check for an individual vehicle.
| Make / Model | Years | Variant | Engine | Status |
|---|---|---|---|---|
| IVECO Daily IV | 2006–2011 | 35C | 2.3 | Catalog documented |
| IVECO Daily IV | 2006–2011 | 35C | 3.0 | Catalog documented |
| IVECO Daily IV | 2006–2011 | 35S | 2.3 | Catalog documented |
| IVECO Daily IV | 2006–2011 | 35S | 3.0 | Catalog documented |
| IVECO Daily IV | 2006–2011 | 50C | 3.0 | Catalog documented |
| IVECO Daily IV | 2006–2011 | 65C | 3.0 | Catalog documented |
Vehicles / applications NOT confirmed by this research
| Vehicle / application | Fitment position | Action before purchase |
|---|---|---|
| IVECO Daily 2014-on | Not verified for this part-number family | Do not order from eBay's broad compatibility table alone. Send VIN. |
| IVECO Daily before 2006 | Not confirmed across the range | Conflicting used-parts data exists. Match VIN and physical part number/shape. |
| Any Daily with different duct shape, mounting points or part number | Not confirmed | Compare photos and send VIN before ordering. |
| Other makes / unrelated models | No confirmed cross-application found | Do not buy on dimensions or appearance alone. |
Door count/body configuration is not being guessed or used as a shortcut. This part is being identified by its part-number family, physical shape and documented Daily variants. VIN decoding is the safest final fitment check.
Part Identification & Technical Detail
Construction
Material: moulded plastic (catalog specification for the cross-reference family).
Placement: front / engine compartment, behind the front fascia area and feeding the air-filter inlet route.
Reference weight: approximately 0.33 kg for cross-reference 504345694.
Reference dimensions
One catalog reference for 504345694 lists approximately 300 × 470 × 100 mm. Catalog dimensions can depend on measuring method, so use the actual-item photographs and VIN/part-number check rather than dimensions alone.
Condition: used. Please inspect all actual-item photographs for condition, marks, openings and mounting points.
Symptoms of a Damaged Intake Duct
- Visible cracking, splitting, impact damage or deformation.
- Broken or weakened mounting points causing a loose duct.
- Rattling or vibration from the front fascia / intake area.
- Changed or unusually loud intake resonance from the front of the vehicle.
- Poor seating where the duct meets the air-filter housing or front pickup.
- Debris, moisture or contamination visible around an improperly seated inlet route.
- Collapsed, obstructed or distorted ducting restricting the intended inlet path.
- Previous repair/tape work indicating the original duct has deteriorated.
These are typical inspection symptoms for a damaged inlet duct, not a diagnosis of every engine or drivability fault. Diagnose the vehicle properly before replacing parts.
Why Choose a Used Original Factory-Fit Part?
Correct moulded geometry
A factory-fit duct is formed around the intended mounting points, surrounding clearances and air-box connection for the applications it was designed for.
Known mounting design
Original clip positions, neck profile and moulded mounting features reduce the risk of forcing a poorly shaped low-cost copy into place.
Reuse can save money
Buying a good used part keeps a serviceable component in circulation. On some parts, used pricing can be substantially below new pricing; ThePartPilot states savings can be as much as 70% on selected parts, depending on the current new-part price.
General Fitting Guide
- Park safely, switch the ignition off, remove the key and allow the engine/front components to cool.
- Locate the existing front intake duct running from the front fascia/grille pickup area toward the air-filter housing. Compare the replacement shape and mounting points before dismantling.
- Remove only the upper trim or grille-access pieces needed for access, if fitted. Keep all clips and fasteners organised.
- Release the duct's retaining clips, screws or bolts without forcing brittle surrounding plastic.
- Disengage the old duct from the air-filter housing/front pickup connection. Note its exact orientation and routing.
- Inspect the air-box inlet neck, surrounding seals/grommets and mounting clips. Replace damaged retaining hardware where necessary.
- Install the replacement in the same orientation. Fully seat each connection before tightening or clipping it into place.
- Refit removed trim. Check that the duct is secure, does not rub moving/hot components, and is not pinched or obstructed.
- Start the engine and listen for unusual vibration or intake noise. Re-check the installation visually before road use.
Tools commonly required
Trim clip toolScrewdriversMetric socket setRatchetTorx bit set as fittedTorch/work lightGlovesExact fastener types vary; inspect your vehicle before starting rather than assuming a specific Torx or socket size.
Estimated labour time
Planning estimate: approximately 0.3–0.5 hour (18–30 minutes) for an experienced technician with normal access.
This is not a manufacturer book time. Corroded fasteners, damaged trim, previous repairs or additional fascia removal can increase labour.
Garage Labour Cost Estimator — No JavaScript
eBay does not allow active-content calculators, so this listing uses a simple transparent formula and lookup table. Using a conservative 0.5-hour planning allowance:
Fitting, Repairs, Collection & Stock
Fitting & repair service
Fitting and repair work may be available subject to workshop availability and prior appointment. Message us through eBay before travelling or purchasing if you want to ask about a fitting slot and price.
Collection
Collections are available 7 days a week until 8pm by prior appointment, including bank holidays by prior arrangement. Confirm the appointment through eBay Messages before travelling.
Worldwide Postage Through eBay
This item can be offered internationally through eBay's supported international delivery programmes where the item, destination and buyer are eligible. The options displayed by eBay at checkout are the final authority for your address.
Current UK Global Shipping Programme destination list checked 8 August 2026:
Non-EU: Antigua and Barbuda, Aruba, Australia, Bahamas, Bahrain, Bangladesh, Barbados, Belize, Bermuda, Bolivia, Brazil, Brunei Darussalam, Cambodia, Canada, Cayman Islands, Chile, China, Colombia, Costa Rica, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, French Guiana, Grenada, Guadeloupe, Guatemala, Guernsey, Honduras, Hong Kong, Iceland, Indonesia, Israel, Jamaica, Japan, Jersey, Jordan, Kuwait, Liechtenstein, Macau, Malaysia, Maldives, Martinique, Mexico, Monaco, Montserrat, New Zealand, Nicaragua, Norway, Oman, Pakistan, Panama, Paraguay, Peru, Philippines, Qatar, Reunion, Saint Kitts and Nevis, Saint Lucia, Saudi Arabia, Singapore, South Africa, South Korea, Sri Lanka, Switzerland, Taiwan, Thailand, Trinidad and Tobago, Turks & Caicos Island, UAE, Ukraine, Uruguay, USA, Vietnam.
eBay announced that GSP sellers are being upgraded to eBay International Shipping in phases from August 2026, so the exact programme name and destination availability shown at checkout may change after this description is published.
How to find us / WhatsApp
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
VAT, Checkout Address & Returns
VAT Global Accounting / Margin Scheme
Eligible second-hand goods are supplied under the applicable VAT margin / Global Accounting scheme. VAT is not shown as a separate amount on the sale price/invoice under the margin scheme.
Checkout address
Please make sure your eBay checkout delivery address is complete and correct before paying. We cannot simply redirect an order to a different address after checkout; use the address controls provided by eBay before completing payment.
Returns — fitment accuracy matters
This listing currently offers 30-day returns. Business-seller returns are handled under eBay's return rules and applicable consumer law. No restocking fee is stated in this description. Where eBay's seller-protection rules permit a deduction because an item is returned used, altered, incomplete or damaged, any deduction should reflect the actual loss in value and the applicable eBay process.
Help us avoid unnecessary returns: compare the actual-item photos, check the part numbers and send the VIN through eBay Messages before buying if fitment is uncertain.
Support a Local Parts Business & Keep Good Parts in Use ♻️🌍🔧📦
Buying a quality used vehicle part supports a local specialist parts business while extending the useful life of a component that might otherwise be discarded. Reuse can reduce demand for manufacturing and shipping a brand-new replacement, save usable material from waste streams and keep more value in the circular economy.
Every correctly matched used part also avoids the extra transport, packaging and handling created by a preventable wrong-order return. That is why ThePartPilot puts part-number matching, photo comparison and VIN verification at the centre of the listing.
Before You Buy — 60-Second Fitment Checklist
- Check your existing part for 504139775, 504193548 or 504345694 where visible.
- Compare the moulded shape, openings and mounting points with all actual-item photos.
- Confirm your vehicle is within a documented 2006–2011 Daily application above.
- If any detail is uncertain, send the full VIN through eBay Messages and wait for a fitment check before purchasing.
- Check your delivery address carefully before completing eBay checkout.
Correct part. Correct vehicle. First time.