Nissan Pixo 09-13 Suzuki Alto 09-15 5DR LH Front Rear Inner Handle 83130-75J0
Nissan Pixo 09-13 Suzuki Alto 09-15 5DR LH Front Rear Inner Handle 83130-75J0
This listing is for the left-hand interior door release handle assembly shown in the actual item photographs. The moulded markings visible on the supplied part are 83130-75J0, LH and PA6-GF30. Nissan catalogue cross-reference: 80671-4A00F.
The same catalogue number is used for the front-left and rear-left interior door positions on the compatible 5-door vehicles below. Always compare the shape, mounting points, colour and moulded number with the part removed from your vehicle. For final VIN confirmation, send the complete 17-character VIN through eBay Messages before ordering.
You will receive the used component shown. Cosmetic marks consistent with previous use may be present; inspect all photographs before purchase.
| Make / Model | Exact Production Range | Body / Engine | Position | Number Check |
|---|---|---|---|---|
| Nissan Pixo UA0 / UA0-RHD | 03/2009-08/2013 | 5-door hatchback, 1.0 3-cylinder petrol | Front Left or Rear Left |
80671-4A00F Cross-ref 83130-75J0 |
| Suzuki Alto, UK/EU model | 03/2009-03/2015 | 5-door hatchback, 1.0 petrol | Front Left or Rear Left |
83130-75J0 Old part must match |
• 3-door vehicles or a different Alto/Pixo body generation.
• Suzuki Celerio or later replacement models.
• Any vehicle where the old handle does not show 83130-75J0, or the Nissan catalogue number is not 80671-4A00F.
• Any other rebadged model unless its VIN catalogue and original part number confirm the same component.
Registration lookup alone is not sufficient because trim and production changes can vary. Send the complete VIN through eBay Messages and compare your old component with the actual photographs before purchase.
Interior door release handle assembly
LH / left / UK nearside
Front left or rear left
83130-75J0 PIA-02
80671-4A00F
PA6-GF30 glass-fibre-reinforced nylon housing with metal mechanism
Grey housing with silver-tone pull lever
Used; inspect photographs for cosmetic condition
Pulling the lever operates the door-latch release through the connected cable or linkage, allowing the door to open from inside the cabin. The assembly also supports the interior lock indication/lever arrangement. A damaged handle may prevent normal interior opening even when the external handle still works.
• Lever feels loose, detached or has excessive travel.
• Cracked handle, broken pivot or damaged mounting point.
• Handle does not return correctly after being pulled.
• Cable or linkage repeatedly comes away because the retaining point is damaged.
• Visible wear or damage around the lock indicator.
Diagnosis note: If the cable, linkage, latch or door lock is seized or broken, replacing the handle alone may not cure the fault. Inspect the complete mechanism before ordering.
A matching factory-fit used component preserves the original mounting geometry, cable position, lever travel, trim alignment and finish. Cheap copy parts can vary in moulding tolerance, material strength and colour, which may cause poor alignment, rattles or premature failure.
Buying used can also cost substantially less than a new dealer-supplied part. Savings vary by part and current new-part price, so compare like-for-like numbers before purchase.
Plastic trim-removal tools, Phillips screwdriver, small flat screwdriver or pick, suitable Torx bits, small socket set, magnetic parts tray and protective gloves. Fastener type may vary by door trim.
- Park safely, switch the ignition off and lower the window for easier handling.
- Remove the trim cap around the interior handle and remove the retaining screw.
- Remove the door-pull and door-card fasteners, then release the perimeter clips with a plastic trim tool.
- Lift the door card from the window ledge. Disconnect any electrical plugs fitted to the door card.
- Release the handle cable or linkage from the old assembly without bending it.
- Remove the handle retaining fastener and withdraw the old assembly.
- Install the replacement in the same orientation, reconnect the cable/linkage and secure the fastener.
- Test the interior release and lock operation several times before refitting the door card.
- Refit the door card, clips, electrical connectors and screws. Confirm that the door opens, closes and locks correctly.
Workshop advice: These are general fitting instructions, not a substitute for the manufacturer repair manual. Stop if the latch or linkage is damaged, seized or incorrectly adjusted.
Typical experienced-technician time: approximately 0.5-1.0 hour, depending on door position, seized fasteners, damaged trim clips and any related latch fault.
| Garage Rate | 0.5 Hour | 0.75 Hour | 1.0 Hour |
|---|---|---|---|
| £60/hour | £30 | £45 | £60 |
| £80/hour | £40 | £60 | £80 |
| £100/hour | £50 | £75 | £100 |
| £120/hour | £60 | £90 | £120 |
Static estimate: hourly rate multiplied by booked labour time. Labour, diagnostics, clips and additional damaged parts are not included in the item price. Fitting and repair services may be available subject to workshop capacity; enquire through eBay Messages.
UK and international delivery: International orders are sent to eligible destinations through eBay's Global Shipping Programme. Availability, postage, import charges and delivery estimates are calculated by eBay and shown at checkout.
Collection: Available by prior appointment, 7 days a week until 8pm, including bank holidays where agreed in advance. Arrange collection through eBay Messages.
Address warning: Ensure the delivery address is correct before payment. We cannot change the checkout address after purchase; an incorrect-address order may need to be cancelled and placed again.
How to find us / WhatsApp
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
Returns are handled under the return terms displayed by eBay on this listing and applicable consumer law. Please perform the part-number, side, body-style and VIN checks before fitting.
Where eBay permits, a deduction may apply only for the actual loss in value caused by returning an item used, altered, incomplete, fitted beyond reasonable inspection, or damaged through insecure packaging. This is not a blanket restocking charge.
Where eligible, this used part is sold under the Global Accounting VAT Margin Scheme. VAT is accounted for within the selling price and is not shown separately; there is no separately reclaimable VAT amount.
♻ Choosing a serviceable used component keeps useful material in circulation, reduces demand for new manufacturing and helps prevent avoidable automotive waste. Thank you for supporting an independent parts business and responsible vehicle recycling.