NISSAN PULSAR C13 1.5 dCi 2014-2018 AIR INTAKE TURBO HOSE PIPE 1207600

NISSAN PULSAR C13 1.5 dCi 2014-2018 AIR INTAKE TURBO HOSE PIPE 1207600

£24.34
Skip to product information
NISSAN PULSAR C13 1.5 dCi 2014-2018 AIR INTAKE TURBO HOSE PIPE 1207600

NISSAN PULSAR C13 1.5 dCi 2014-2018 AIR INTAKE TURBO HOSE PIPE 1207600

£24.34
THEPARTPILOT
NISSAN PULSAR C13
1.5 dCi AIR INTAKE / TURBO HOSE
Used Original-Manufacturer Specification Replacement Part
THEPARTPILOT • THEPARTPILOT • THEPARTPILOT
⚠ FITMENT — PLEASE READ BEFORE ORDERING

This listing is for an air-intake / turbo air hose identified in the original listing by reference 1207600.

Current research supports application to the Nissan Pulsar C13 1.5 dCi diesel. Do not order solely because you own a Nissan Pulsar. The C13 was also supplied with petrol engines which use different induction components.

For maximum accuracy, compare the shape, mouldings, connector positions, mounting points and every visible number on your existing hose with the listing photographs. If uncertain, contact us with your VIN before ordering.

🚘 Vehicle Application

Nissan Pulsar C13 5 door reference vehicle

Vehicle reference image only — Nissan Pulsar C13 five-door hatchback. The vehicle shown is not the donor vehicle.

Vehicle Years Engine Status
Nissan Pulsar C13 5 Door 2014–2018 1.5 dCi / K9K family Supported application — VIN/number check recommended
Nissan Pulsar C13 2014–2018 1.2 DIG-T Petrol DO NOT ASSUME FITMENT
Nissan Pulsar C13 2015–2018 1.6 DIG-T Petrol DO NOT ASSUME FITMENT

🔎 Identification & Part Numbers

Listing Reference 1207600
Cross-reference found in catalogues 165763328R — VERIFY AGAINST ACTUAL PART / VIN BEFORE ORDERING
Component Air intake / induction hose-pipe
Location Engine compartment / induction system

⚙️ What Does This Part Do?

This hose forms part of the engine's air-management / induction system. Its job is to provide a correctly sealed route for airflow through the relevant section of the intake system.

Because turbo-diesel induction systems depend on controlled airflow, splits, damaged seals, distorted connections or loose joints can cause air leakage and adversely affect engine performance.

Possible symptoms of a damaged intake hose

⚠ Hissing or rushing-air noise under acceleration
⚠ Reduced engine performance
⚠ Poor throttle response
⚠ Abnormal turbo/boost behaviour
⚠ Engine-management warning light in some fault conditions
⚠ Visible cracking, splitting or oil staining around a leaking joint
⚠ Excessive smoke in some air/boost leak conditions

These symptoms can have several causes and do not by themselves diagnose this hose as faulty. Proper inspection or diagnostic testing is recommended.

⭐ Why Buy a Used Original-Manufacturer Part?

A correctly identified used factory-specification component was manufactured to the dimensions, connector geometry and material requirements of the original vehicle. This can be preferable to an inexpensive pattern copy where moulding accuracy, material quality and connector dimensions may vary.

Buying quality used vehicle components can also provide a substantial saving compared with purchasing a new replacement. Depending on the component and current new-part pricing, used parts can sometimes cost significantly less.

♻ Reusing serviceable automotive components also keeps usable parts in circulation and reduces demand for unnecessary new manufacturing.

🔧 General Fitting Guide

Estimated workshop time: approximately 0.5–1.0 hour where straightforward access is available. Actual time varies by vehicle condition, fasteners and technician.

Typical tools:

• Metric socket set
• Ratchet and extensions
• Screwdrivers / suitable hose-clamp driver
• Hose-clamp pliers where applicable
• Trim tool where surrounding ducting must be moved
• Inspection lamp
• Suitable PPE

General procedure:

1. Allow the engine to cool and secure the vehicle.
2. Locate the existing intake hose in the engine compartment.
3. Photograph the original routing and connections before dismantling.
4. Remove any necessary intake covers or ducting.
5. Release the hose clamps / retaining fittings carefully.
6. Remove the old hose without damaging adjoining plastic fittings.
7. Inspect connecting surfaces, seals and clamps.
8. Compare the replacement part directly with the removed component.
9. Install it in the original orientation and fully seat each connection.
10. Refit clamps and removed components.
11. Start the engine and inspect for leaks, abnormal noise or warning lights.

This is a general guide rather than manufacturer workshop data. Professional installation is recommended where you are not competent to perform the repair safely.

💷 Garage Labour Cost Estimator

Formula: Labour Rate × Repair Time = Estimated Labour Cost

Hourly Rate 30 Minutes 1 Hour
£50/hr £25 £50
£70/hr £35 £70
£90/hr £45 £90
£120/hr £60 £120
£150/hr £75 £150

🔧 THEPARTPILOT fitting/repair service may also be available by prior arrangement, subject to workshop availability.

📦 More Than 25,000 Parts In Stock

THEPARTPILOT carries more than 25,000 vehicle parts on the shelf at any one time, helping customers source replacement components quickly.

Automotive parts warehouse reference image

Warehouse reference image for illustration.

🌍 UK & International Delivery

International orders can be shipped through eBay's eligible international shipping programme where the listing and destination qualify. Availability is determined by eBay at checkout and can change by destination and product category.

International tracking and customs processing are handled according to the eBay programme applicable to the transaction.

IMPORTANT DELIVERY NOTICE
Please ensure the delivery address entered at eBay checkout is complete and correct. We cannot manually substitute a different delivery address after checkout.

📍 Collection Available

Collections available 7 days a week until 8PM by prior appointment, including Bank Holidays where arranged in advance.

WhatsApp

WhatsApp QR code for THEPARTPILOT

Scan the QR code to contact THEPARTPILOT on WhatsApp.

✅ Buy The Correct Part First Time

Vehicle compatibility is extremely important. Please compare your existing component against the listing photographs and part markings before purchasing.

If you are unsure, contact us before ordering with your full 17-character VIN and, where possible, photographs/part numbers from your existing component.

We will use the available identification information to help check compatibility. A model/year match alone should never be treated as proof where different engines or part revisions were fitted.

↩ Returns & Ordering

Please review the eBay listing's current return terms before purchase. Buyers remain responsible for selecting the correct component using the supplied fitment information, photographs and identification numbers.

Nothing in this description limits statutory consumer rights or protections provided by eBay.

🧾 VAT Information

Where the transaction is sold under an applicable second-hand goods margin scheme, VAT is not separately itemised or reclaimable on the invoice.

🚗 WE ALSO BUY CARS FOR CASH

Nationwide collection available • Fast valuation process • Same-day payment where agreed

💛 Support Independent Automotive Recycling

Every purchase helps support an independent UK automotive parts business. Choosing a serviceable used component gives an existing part another useful life, helps reduce automotive waste and can reduce the resources required to manufacture a completely new replacement. ♻️🌍🚗

Thank you for choosing THEPARTPILOT and helping keep usable automotive components in circulation.

THEPARTPILOT
PARTS • FITMENT SUPPORT • REPAIRS • COLLECTION
THEPARTPILOT • THEPARTPILOT • THEPARTPILOT

You may also like