Skoda Octavia MK2 1Z 2004-2013 Rear Parking PDC Sensor 1K0919275
Skoda Octavia MK2 1Z 2004-2013 Rear Parking PDC Sensor 1K0919275
Škoda Octavia MK2 1Z Rear Parking PDC Ultrasonic Sensor
Used original-equipment specification ultrasonic parking assistance sensor. Please identify your existing component by part number, connector, physical design and vehicle specification before ordering.
Do not order from registration/year alone. VAG vehicles can use different parking-assistance systems during the same production year.
The component offered is identified as 1K0 919 275 / 1K0919275. Compare this number and the photographs against the sensor removed from your vehicle.
If you are uncertain, contact us before purchasing with your 17-character VIN and, ideally, a clear photograph of your existing sensor. We can check compatibility rather than guessing.
🔎 PART SPECIFICATION
| Manufacturer / Vehicle Group | Škoda / Volkswagen Group application |
| Part Number | 1K0919275 / 1K0 919 275 |
| Superseding Reference | 3D0998275A — verify by VIN before substitution |
| Component | Ultrasonic parking distance / PDC sensor |
| Listed Position | Rear bumper — listing identifies rear/right application |
| Electrical Connection | 3-pin type — visually compare connector before ordering |
| Operating Principle | Ultrasonic distance measurement |
| Condition | Used — cosmetic marks consistent with previous installation may be present |
🚘 ŠKODA OCTAVIA II / MK2 FITMENT GUIDE
The 1K0919275 part number is catalogued for Octavia II 1Z applications. The table is an identification guide rather than permission to ignore the part number fitted to your individual vehicle.
| Vehicle | Chassis | Body | Production Range | Requirement |
| Škoda Octavia II / MK2 | 1Z3 | Hatch / Liftback | 2004–2013 model family | Must use matching PDC sensor specification |
| Škoda Octavia II / MK2 | 1Z5 | Estate / Combi | 2004–2013 model family | Must use matching PDC sensor specification |
⚠️ Production range does not mean every Octavia produced during these years contains this sensor. Parking-assistance equipment varies. Part-number/VIN confirmation takes priority.
❌ DO NOT ORDER IF...
• Your existing sensor carries a different, non-interchangeable part number.
• Your connector shape or pin arrangement differs from the photographed part.
• Your vehicle does not have the corresponding factory parking-assistance system.
• You are relying solely on registration number, model year or visual similarity.
• The bumper sensor mounting arrangement differs from your existing installation.
Unsure? Send us the VIN and a photograph of your original component before buying.
📍 WHERE THE SENSOR IS FITTED
This ultrasonic sensor installs into a dedicated holder behind the rear bumper skin. Its sensing face is visible externally as a small circular section of the bumper. The sensor connects to the parking-assistance wiring loom behind the bumper.
📡 WHAT DOES THIS PART DO?
The parking distance sensor emits ultrasonic pulses toward objects behind the vehicle. Reflected signals are interpreted by the parking-assistance system to estimate distance. The driver is then warned by the vehicle's parking-aid indication/buzzer system, depending on specification.
A correctly functioning sensor is particularly useful when manoeuvring close to walls, parked vehicles, posts and other obstacles that may be difficult to see directly from the driver's seat.
⚠️ COMMON SYMPTOMS OF A FAILED PDC SENSOR
• Parking assistance produces a continuous warning tone or fault indication.
• One sensor does not respond while the other sensors operate normally.
• Parking assistance becomes unavailable or intermittently switches off.
• Diagnostic equipment reports a parking sensor circuit/signal fault.
• Incorrect or inconsistent obstacle-distance warnings.
• Visible impact, water ingress, corrosion or connector damage.
Always diagnose the system before replacing components. Wiring, connectors, sensor holders and the parking-assistance control system can produce similar symptoms.
⭐ WHY CHOOSE A USED ORIGINAL-EQUIPMENT PART?
An original vehicle-manufacturer specification component was designed around the vehicle's electrical architecture, mounting system and parking-assistance calibration. A correctly matched used original part can therefore be a strong alternative to an unknown low-cost copy.
Buying quality used vehicle components can also offer substantial savings compared with buying equivalent components new. Depending on the component and current new retail price, used parts can sometimes cost considerably less — in some cases savings can approach 70%.
The critical point is correct identification: always match the number and specification rather than assuming that similar-looking sensors interchange.
🔧 FITTING GUIDE
Typical skill level: Intermediate
Approximate workshop time: 0.5–1.5 hours depending on bumper access, corrosion and vehicle specification.
Typical tools:
• Trim-removal tools
• Suitable Torx/socket set for vehicle fasteners
• Ratchet and extensions
• Small pick/release tool for electrical connector
• Protective gloves
• Diagnostic scanner recommended for fault confirmation/clearing
General procedure:
1. Confirm the failed sensor by diagnostic testing before dismantling.
2. Secure the vehicle and switch the ignition off.
3. Obtain safe access behind the relevant rear-bumper section; bumper removal may be required depending on specification.
4. Locate the parking sensor and inspect the loom/connector for damage or corrosion.
5. Release the electrical connector without pulling on its wiring.
6. Carefully release the sensor from its bumper holder.
7. Compare old and replacement components side-by-side, including number and connector.
8. Install the replacement in the correct orientation and ensure the retaining clips are fully engaged.
9. Reconnect the wiring and reassemble removed trim/bumper components.
10. Test the parking-assistance system before returning the vehicle to service.
This is a general workshop guide, not a substitute for the manufacturer's vehicle-specific repair procedure. If unsure, use a competent automotive technician.
💷 GARAGE LABOUR COST ESTIMATOR
JavaScript calculators are not used in this listing. Use the static guide below: multiply your garage's hourly labour rate by the actual fitting time.
| Hourly Rate | 0.5 Hour | 1.0 Hour | 1.5 Hours |
| £50/hr | £25 | £50 | £75 |
| £75/hr | £37.50 | £75 | £112.50 |
| £100/hr | £50 | £100 | £150 |
| £125/hr | £62.50 | £125 | £187.50 |
Labour figures are examples only. Actual workshop charges vary by garage, location and the condition/specification of the vehicle.
📦 25,000+ PARTS IN STOCK
THEPARTPILOT carries more than 25,000 vehicle parts in stock and on the shelf at any one time. Our goal is straightforward: identify the component accurately, supply the correct part and reduce unnecessary returns.
✅ BUY THE CORRECT PART FIRST TIME
Before checkout:
① Compare 1K0919275 with your removed component.
② Compare connector shape and physical construction.
③ Confirm the vehicle has the appropriate PDC system.
④ Compare the listing photographs with your original part.
⑤ If there is any uncertainty, provide the VIN before ordering.
VIN verification is strongly recommended where the original part number cannot be read.
📮 IMPORTANT DELIVERY ADDRESS NOTICE
Please ensure your checkout delivery address is completely correct before payment. We cannot manually change an address after the order has been placed. This protects both buyer and seller and ensures the parcel is processed using the address supplied through eBay checkout.
🌍 UK & INTERNATIONAL DELIVERY
UK delivery is available according to the postage service shown in the listing. International orders can be handled through eBay's available international shipping programme where the destination and item are eligible.
The exact countries available are determined dynamically by eBay according to destination, item category, carrier restrictions and programme eligibility. Please use the postage section of this listing to confirm availability to your country before purchasing.
📍 COLLECTION AVAILABLE
Collections available 7 days a week until 8PM by prior appointment, including Bank Holidays by prior appointment.
Please arrange collection before travelling so that the item can be located and prepared for you.
🧰 REPAIRS & FITTING
Need the component installed? THEPARTPILOT also offers vehicle repair and component-fitting services subject to workshop availability. Contact us before travelling for availability and an estimate.
Nationwide collection available • Same-day payment subject to agreed purchase and collection arrangements.
🧾 VAT INFORMATION
Used parts are supplied under the applicable margin scheme. VAT is not separately charged or shown as a reclaimable VAT amount.
↩️ RETURNS & FITMENT
Please refer to the returns terms displayed by eBay on this listing for the applicable return period and postage arrangements.
Incorrect ordering can often be avoided. We therefore strongly encourage buyers to compare the part number and photographs and request VIN assistance before purchasing where fitment is uncertain.
Nothing in this description limits any statutory consumer rights or applicable eBay buyer protections.
SUPPORT A SMALL BUSINESS — REUSE QUALITY PARTS
Purchasing a serviceable used vehicle component gives an existing part another working life and can reduce demand for replacement manufacturing, packaging and premature disposal. Reusing components is one practical way of keeping useful automotive material in circulation for longer.
Every purchase also supports an independent UK automotive parts business. Thank you for choosing THEPARTPILOT.
MATCH THE NUMBER • COMPARE THE PHOTOS • CHECK THE CONNECTOR • ASK IF UNSURE
© THEPARTPILOT • Listing content and branding protected.