AUDI A2 8Z 2000-2005 REAR BUMPER BLACK 8Z0807417 FREE POSTAGE
AUDI A2 8Z 2000-2005 REAR BUMPER BLACK 8Z0807417 FREE POSTAGE
Audi A2 8Z Rear Bumper
The Correct Rear Bumper Starts With The Correct Number
This listing is for the photographed Audi A2 Type 8Z / 8Z0 rear bumper , identified by reference 8Z0807417. It is the exterior rear bumper skin with the visible silver-finish mouldings and tow-eye access cover shown in the photographs.
This panel forms the rear exterior finish, follows the vehicle's quarter-panel contours, carries the decorative strips and provides access to the towing-eye mounting point. It does not replace the separate crash reinforcement, energy absorber, side guides or structural mounting hardware.
Study Every Image Before Ordering
The supplied photographs show pronounced scratches, scuffs, handling marks and general cosmetic wear across the outer face. Budget for cleaning, preparation, local plastic repair where required and refinishing if a high cosmetic standard is expected. Colour and paint code are not guaranteed. The photographs form an essential part of the condition description.
Item Details & Specifics
Compatibility Guide
Fits: 2000 - 2005 Audi A2 Type 8Z / 8Z0 (00-05 Reg range) only when the part number, moulding profile, trim layout, tow-eye position and mounting points match the buyer's existing bumper.
| Vehicle | Years | Chassis | Location | Mandatory Match Checks |
|---|---|---|---|---|
| Audi A2 | 2000, 2001, 2002, 2003, 2004, 2005 | 8Z / 8Z0 | Rear bumper | 8Z0807417, exterior shape, silver-strip arrangement, tow-eye cover position, sensor-hole configuration and inner mounting tabs |
Registration year alone is not conclusive. Production changes, special-edition trim, previous repairs and retrofits can alter the bumper specification.
Will Not Fit / Exclusion List
Do Not Order For
- Any Audi model other than the A2 Type 8Z / 8Z0.
- A front bumper, reinforcement beam, absorber or mounting bracket requirement.
- A bumper with a different moulding profile, trim-strip layout or tow-eye location.
- A vehicle requiring visible parking-sensor apertures unless the buyer plans professional modification.
- A guaranteed colour match; the paint code has not been verified and the panel is heavily marked.
Special Checks
- Compare the complete stamped / moulded number, including any suffix on your old part.
- Check 1.2 TDI aerodynamic trim and special-edition body details visually rather than assuming.
- Compare every mounting tab and side-return shape using the high-resolution photographs.
- Confirm whether your vehicle has parking sensors, non-standard trim or previous body repairs.
- Send clear photos through eBay Messages before ordering when any detail differs.
What This Component Does
Exterior Function
Creates the visible rear bumper surface, aligns with the rear quarter panels, supports the decorative strips and shields adjacent fittings from everyday road spray and minor contact.
Structural Clarification
This plastic cover is not the primary crash structure. The separate reinforcement beam, absorbers and body mounts perform the underlying load-management role and are not included unless visibly shown.
Systems Controlled
The bumper does not actively control the engine, transmission, braking or drivetrain. Any parking-assistance function depends on separate sensors, holders, wiring and control modules.
Why Production-Fit Geometry Matters
Correct moulding contours, clip locations, ribbing, side returns and trim alignment generally provide a more predictable body fit than low-cost pattern copies with weaker or less accurate mounting geometry.
Premium Recycled Parts — Up To 70% Saving
ThePartPilot holds more than 25,000 parts on the shelves. On selected lines, choosing a carefully identified recycled production-fit component can save up to 70% compared with purchasing the equivalent brand-new component. Savings vary by part, specification, availability and market price.
Tools, Preparation & Fitting Steps
Suggested Tools
- Vehicle lift, approved ramps or trolley jack with correctly rated axle stands.
- Metric socket set, ratchet, extensions and suitable Torx-bit set.
- Non-marring trim-clip and panel-release tools.
- Torque wrench and the vehicle-specific tightening data.
- Masking tape, protective blankets, panel stand and suitable PPE.
- A second technician to support the bumper during removal and alignment.
Before Starting
- Place both bumpers side by side and verify every contour, aperture and mounting point.
- Inspect side guides, absorbers and the reinforcement for hidden impact damage.
- Confirm all clips, screws and retainers required for refitting are available.
- Complete plastic repair and paint preparation before final installation where practical.
- Secure the vehicle on level ground, isolate any relevant electrical equipment and protect adjacent paintwork.
- Remove the rear wheel-arch and lower-edge fasteners; move liners only as far as required for access.
- Remove any luggage-compartment trim necessary to reach concealed rear fasteners, following the workshop manual.
- Disconnect parking-sensor, lamp or accessory wiring where fitted to the vehicle. The listed cover shows no visible sensor apertures.
- Support the bumper across its width, release both side guides evenly and withdraw the cover straight rearward.
- Transfer only serviceable trim and covers. Replace damaged clips, guides or retainers rather than forcing alignment.
- Trial-fit the replacement, check quarter-panel and tailgate gaps, then tighten fasteners to the correct vehicle-specific values.
- Reconnect and test all disturbed electrical equipment, refit liners and trim, then complete a final security and alignment inspection.
Illustrative 4.5-Hour Full-Job Allowance
A 4.5-hour allowance may be used for budgeting when the job includes removal, trim transfer, cleaning, repair preparation, trial fitting and final refitting. It is not an Audi book time or a binding quotation. Paint, materials, parts, curing time and tax are additional where applicable.
| Planning Time | £40 / hr | £60 / hr | £80 / hr | £100 / hr |
|---|---|---|---|---|
| 4.5 hours | £180 | £270 | £360 | £450 |
Free UK Postage & eBay Global Shipping
United Kingdom
Free UK standard postage is included as configured on this listing. The service and final delivery eligibility shown at checkout apply.
International
Eligible worldwide orders are handled through eBay's Global Shipping Programme, including destinations across Europe, the USA, Australia, Canada and other supported regions. Shipping, import charges and taxes are calculated by eBay at checkout.
Protected Packaging
Large exterior panels require careful protection. The bumper will be packed to minimise movement and surface contact during the carrier journey.
Tracking
Dispatch and tracking details are provided through the eBay order record where supported by the selected service.
Customers must ensure their checkout address is correct prior to paying. Due to strict eBay Seller Protection regulations, we are entirely unable to alter or change your delivery address after purchase.
30-Day Returns — Fair, Evidence-Based Terms
The live listing currently provides a 30-day return period. For a full refund, the exact item should be returned complete, securely packaged and in the same condition in which it was supplied. Automotive parts should not be installed, painted, drilled, cut, repaired or altered before a fitment decision is made.
Where an eligible return arrives installed, altered, incomplete, damaged or inadequately packaged, any deduction will reflect the demonstrable reduction in value and will be applied only where eBay policy and UK law permit. There is no automatic 50% restocking charge merely because a buyer changes their mind or orders the wrong variant. Statutory consumer rights remain unaffected.
Match the photographed component, exact stamped number, mounting geometry, trim layout and apertures before installation. Do not rely solely on an automated compatibility dropdown or registration lookup.
Global Accounting VAT Margin Scheme
This eligible second-hand component is sold under the Global Accounting VAT Margin Scheme. VAT is not separately itemised and no reclaimable VAT invoice is available. Where an invoice is issued under the scheme, the required margin-scheme wording is used.
WhatsApp QR for Fitment Help / Appointment Enquiries
Scan the QR code to contact ThePartPilot on WhatsApp for fitment checks, appointments or fitting service availability.For faster fitment help, send your vehicle registration, VIN if available, and clear photos of your existing part, connector and part number.