AUDI A4 B9 8W 2016-2019 REAR LEFT PASSENGER EXTERIOR DOOR HANDLE BRACKET
AUDI A4 B9 8W 2016-2019 REAR LEFT PASSENGER EXTERIOR DOOR HANDLE BRACKET
Rear Left Exterior Door Handle, Carrier Bracket & Bowden Cable
A used factory-original exterior handle assembly removed from an Audi A4 B9/8W. Supplied exactly as photographed, including the painted outer handle, carrier/support bracket and mechanical release cable.
| REAR LEFT / NSR | 4-DOOR A4 B9 | HANDLE + BRACKET | USED PART |
Photo identification: A4 2019 NSR external handle
|
Rear carrier, pivot mechanism and cable shown clearly
|
| LEFT FRONT / NSF | RIGHT FRONT / OSF |
| THIS PART LEFT REAR / NSR |
RIGHT REAR / OSR |
The carrier sits behind the exterior handle skin inside the rear-left door. Pulling the handle operates the Bowden cable and releases the door latch. The small rectangular button/sensor feature must match the equipment on the buyer's existing handle.
| Vehicle | Years used for this listing | Body / chassis | Fitment status |
|---|---|---|---|
| Audi A4 B9 | 2016-2019 | 4-door Saloon, 8W2 / 8WC | Rear-left only; exact physical and equipment match required |
| Audi A4 B9 Avant | 2016-2019 | 5-door Estate, 8W5 / 8WD | Rear-left only; exact physical and equipment match required |
| Audi A4 B9.5 / allroad / S4 / RS4 | Other years or derivatives | Variant dependent | Not confirmed from the photos alone; order only after old-part-number or VIN verification |
| Right rear / OSR door | Either front door |
| Audi A4 B8 / 8K generation | A5 Coupe or Cabriolet two-door models |
| A3, A6, Q-series or unrelated models | A handle with a different button/sensor, cable end or bracket |
| Part type | Exterior rear door handle assembly with carrier/support and Bowden release cable |
| Vehicle position | Rear left / NSR / UK passenger-side rear |
| Colour | Blue metallic as photographed; exact paint code is not confirmed and repainting may be required |
| Construction | Moulded engineering-plastic carrier, painted handle shell, metal pivot/return parts and sheathed mechanical cable |
| Visible equipment | Small rectangular button/sensor style handle; buyer must match this feature |
| Catalogue reference to check | 8W0 837 811 A - rear-left handle base/support family |
| Handle family reference to check | 8W0 837 205 B - exterior handle family reference |
| Included | Only the photographed handle, carrier/bracket and attached cable/components |
| Not included | Door latch, lock actuator, inner handle, door trim, wiring loom or unpictured fixings |
| • Exterior handle feels loose or lifts without releasing the door | • Door opens intermittently or needs repeated pulls |
| • Carrier tabs, pivot points or cable retainers are cracked | • Handle does not return smoothly or sits out of alignment |
| • Bowden cable or yellow cable end has detached or broken | • Button/sensor function is inoperative where the vehicle is so equipped |
A failed exterior handle may prevent convenient entry and can worsen if the cracked carrier or cable is repeatedly forced. Diagnose the latch and electrical equipment as well, because not every opening fault is caused by the handle assembly.
Factory-original components retain the intended mounting geometry, cable routing, clip locations, handle travel and exterior profile. A low-cost copy may look similar online yet differ at the pivot, cable retainer, sensor area or mounting points.
Buying a quality used component can provide a substantial saving compared with a new replacement while keeping a usable part in circulation. Always compare condition and current new-part pricing rather than relying on a fixed saving percentage.
This is a used part and may show age-related marks, light scratches, storage marks or minor cosmetic wear. Study every photograph before purchase. The blue finish is supplied as pictured; colour variation can occur between screens and vehicle paint can fade with age. Exact paint-code matching is not guaranteed.
Typical DIY time: approximately 1.5-3 hours depending on tools and experience.
Difficulty: intermediate; door trim, moisture barrier and handle retaining mechanism must be handled carefully.
Plastic trim-removal tools, Torx bit set, small ratchet or driver, small flat screwdriver/pick, panel-clip pliers, magnetic pickup tool, masking tape, torch and suitable protective gloves.
- Confirm the rear-left door position and compare the replacement assembly with the old part before dismantling.
- Protect the paint and trim. Disconnect the 12V battery where required by the vehicle's workshop procedure, especially when electrical handle equipment is present.
- Remove the rear-left interior door trim and disconnect associated plugs and cables carefully.
- Peel back the moisture barrier without tearing it or contaminating the sealing surface.
- Access the exterior handle retaining fastener from the door edge. Do not fully remove a captive fastener unless the workshop procedure instructs it.
- Release the handle/end cap, disconnect the Bowden cable and any handle electrical connection, then remove the carrier.
- Transfer any required trim or seals, install the replacement carrier and confirm the cable is seated and routed without kinks.
- Test handle movement, latch release, locking and button/sensor operation before resealing and refitting the door trim.
- Restore the moisture barrier fully to reduce the risk of water ingress and wind noise.
Active calculators are not used in this listing. The table below shows labour-only estimates for the expected 0.75-1.50 hour fitting range.
| Garage rate | 0.75 hour | 1.00 hour | 1.50 hours |
|---|---|---|---|
| £50/hour | £37.50 | £50.00 | £75.00 |
| £60/hour | £45.00 | £60.00 | £90.00 |
| £75/hour | £56.25 | £75.00 | £112.50 |
| £90/hour | £67.50 | £90.00 | £135.00 |
| £110/hour | £82.50 | £110.00 | £165.00 |
| £130/hour | £97.50 | £130.00 | £195.00 |
Illustrative labour only. Diagnostics, clips, seals, paintwork, local taxes and additional repairs can change the final garage bill.
- Confirm your vehicle is an Audi A4 B9/8W and identify the exact body style.
- Confirm you need the rear-left / NSR exterior handle on a UK right-hand-drive vehicle.
- Compare the small rectangular button/sensor feature with your old handle.
- Compare the carrier moulding, mounting holes, cable routing and yellow cable end against the listing photographs.
- Check the moulded number on your existing carrier or verify by VIN.
- When unsure, send the registration or VIN plus a clear old-part photo through eBay Messages before ordering.
| Dispatch | Tracked dispatch service. Orders completed before the stated cut-off are prioritised for prompt processing. |
| International delivery | Available through eBay's international shipping services to eligible destinations shown at checkout. Availability varies by item, location and buyer address. |
| Checkout address | The buyer must enter the correct delivery address before payment. The address cannot be changed after checkout. |
| VAT treatment | Sold under the Global Accounting VAT margin scheme where applicable. VAT is not shown separately and is not reclaimable. |
Please complete the fitment checks above before installation. The exact item supplied must be returned in the same condition, with all included parts and secure protective packaging.
|
25,000+ parts held in stock |
99.6% positive feedback shown on eBay |
30 DAYS seller warranty on this listing |
WhatsApp QR for Fitment Help / Appointment Enquiries
Scan the QR code to contact ThePartPilot on WhatsApp for fitment checks, appointments or fitting service availability.For faster fitment help, send your vehicle registration, VIN if available, and clear photos of your existing part, connector and part number.
📦 Parts are checked against their photographs, protected for transit and dispatched from organised stock. The photographs in this description show the actual item rather than a generic internet image.
♻️ Choosing a reusable used part supports the circular economy by extending the service life of an existing component, reducing avoidable waste and lowering demand for newly manufactured replacements.
🤝 Every purchase supports a local small business, our dismantling, parts-checking, warehouse and dispatch work, and the continued availability of affordable replacement parts.