CITROEN PICASSO 2011 EXHAUST SENSOR 9662143180
CITROEN PICASSO 2011 EXHAUST SENSOR 9662143180
Citroen Picasso HDi DPF / FAP Differential Pressure Sensor with Twin Hoses
Exact Item You Will Receive
Image reliability: these photographs are served from eBay's own secure image network. The photographs form part of the description; normal cosmetic marks from previous use may be present.
Part Identification & Technical Details
What This Sensor Does
This sensor compares exhaust pressure on the inlet and outlet sides of the diesel particulate filter. It sends the pressure difference to the engine control unit, which uses that information to estimate filter loading and manage the regeneration strategy. The sensor reports data; it does not clean the DPF by itself.
Higher-pressure hose ↘ 9662143180
Differential sensor → Engine ECU
DPF loading data
Lower-pressure hose ↗
Verified Picasso-Family Sensor Compatibility
| Vehicle | Years | Diesel engines / codes listed for this sensor | Decision |
|---|---|---|---|
| Citroen C3 Picasso I, 5-door MPV | 2009–2015 | 1.6 HDi: 9HD, 9HP, 9HR, 9HZ |
Sensor listed Match hoses and connector |
| Citroen C4 Picasso I, 5-seat / Grand 7-seat | 2006–2013 catalogue range | 1.6 HDi: 9HR, 9HY, 9HZ 2.0 HDi: RHE, RHH, RHJ, RHR |
Sensor listed Confirm exact body and engine |
| Citroen Xsara Picasso, 5-door MPV | 2007–2011 | 1.6 HDi: 9HY, 9HZ |
Sensor listed Match full assembly |
A 2011 registration alone is not enough to identify C3 Picasso, C4 Picasso, Grand C4 Picasso or Xsara Picasso. Part number and photographed hose layout take priority over the registration year.
Additional Sensor Cross-Fit Applications
The number 9662143180 is also catalogued across selected Citroen, Peugeot, DS, Fiat, Mini, Mitsubishi, Toyota and Vauxhall/Opel diesel applications. Because this listing is supplied with used hoses, the safest approach is to treat these as sensor-body references only unless the complete assembly matches.
| Make | Selected model families | Catalogue years | Buyer check required |
|---|---|---|---|
| Citroen | Berlingo/Multispace, C2, C3, C4, C5, C6, C8, Dispatch, C-Crosser | Selected diesel applications, 2005–2022 | Exact number, engine code, connector, mounting and hoses |
| Peugeot | 207, 208, 3008, 307, 308, 407, 5008, 508, Expert, Partner, RCZ | Selected diesel applications, 2005–2022 | Exact number and complete hose layout |
| DS | DS 3, DS 4, DS 5 | Selected diesel applications, 2009–2018 | Engine code and physical comparison |
| Other PSA-derived applications | Selected Fiat Scudo/Ulysse, Mini Cooper D, Mitsubishi diesel, Toyota Proace and Vauxhall/Opel PSA-platform models | Varies by model and engine | Do not order from model name alone; verify by number and image |
This Part Will Not Fit
- Will not fit petrol engines or diesel vehicles without the applicable DPF/FAP system.
- Will not fit when your original sensor number is different and is not an approved supersession.
- Will not fit sensors with a different connector shape, pin count, mounting tab or pressure-port orientation.
- Will not fit as a complete assembly when either supplied hose is a different length, bend, end fitting or route.
- Do not assume fitment from “Picasso”, registration year, engine size or item specifics alone.
Common Symptoms of a Faulty Sensor or Blocked Pressure Hoses
Warning lights
Engine-management or DPF warning lamp, sometimes with stored differential-pressure faults such as P2452 or P2453.
Regeneration problems
Failed, interrupted or unusually frequent regeneration because the control unit receives an implausible pressure reading.
Performance changes
Limp-home mode, reduced power, uneven response or increased fuel use can occur.
Diagnosis matters
The same symptoms may be caused by split/blocked hoses, wiring faults or a physically restricted DPF. Diagnose before replacing parts.
Why Choose a Used Original-Manufacturer Part?
Correct physical design
Original connector geometry, pressure-port orientation and bracket design help reduce installation problems when the number and layout match.
Better value
A quality used part can provide a substantial saving compared with a new replacement. Compare current new-part prices to calculate your actual saving.
Lower waste
Reusing a serviceable component keeps material in circulation and reduces demand for newly manufactured parts.
Fitting Guide, Tools & Estimated Repair Time
Typical tools
- 8 mm / 10 mm sockets, ratchet and extension
- Small flat screwdriver or trim tool for connector lock
- Long-nose or hose-clamp pliers
- Penetrating fluid for seized hose fittings
- Gloves, eye protection and diagnostic scan tool
Estimated labour
Typical replacement: approximately 30–60 minutes.
Allow longer where access panels must be removed, hoses are carbon-blocked, fittings are seized or further diagnosis is required.
- Confirm the fault with diagnostic codes and live differential-pressure readings. Check the wiring and both hoses before condemning the sensor.
- Allow the engine and exhaust to cool fully. Isolate the battery only where the vehicle repair procedure requires it.
- Photograph and label the high- and low-pressure hoses so they cannot be reversed.
- Release the 3-pin electrical connector without pulling on the wiring.
- Remove the sensor mounting bolt/clip and carefully disconnect the hoses.
- Inspect both hoses and exhaust take-off pipes for splits, heat damage and carbon blockage. A new sensor will not correct blocked pipes.
- Install the replacement in the same orientation, reconnect the correct hose to each port, secure the bracket and refit the connector.
- Clear relevant fault codes, check live readings at idle and raised speed, and road-test. Carry out a forced regeneration only when diagnostic assessment confirms it is safe and necessary.
Static Garage Labour Cost Calculator — No Active Content
Formula: hourly labour rate × booked time = estimated labour charge. Parts, diagnostics, consumables, VAT and additional repairs may be extra.
| Garage hourly rate | 30 minutes / 0.5 hour | 60 minutes / 1.0 hour |
|---|---|---|
| £50 per hour | £25.00 | £50.00 |
| £75 per hour | £37.50 | £75.00 |
| £100 per hour | £50.00 | £100.00 |
| £125 per hour | £62.50 | £125.00 |
| £150 per hour | £75.00 | £150.00 |
Fitting and garage repair services may be available subject to workshop capacity. Contact us through eBay Messages before travelling or purchasing a fitting slot.
Buy the Correct Part First Time — 7-Point Check
- Read the full number on your old sensor: 9662143180.
- Compare the 3-pin connector shape and locking tab.
- Compare the sensor mounting ear and orientation.
- Compare both pressure-port positions.
- Compare every hose bend, length, heat sleeve and end fitting with the listing photos.
- Check your engine code, not only the registration year.
- When any detail differs, send the VIN or registration and clear photographs through eBay Messages before ordering.
Delivery, Collection, Address & VAT Information
Worldwide delivery
International delivery is available to eligible destinations shown by eBay at checkout through the Global Shipping Programme. eBay determines destination eligibility, import charges and international delivery options.
Checkout address
Orders can only be dispatched to the address selected at checkout. The delivery address cannot be changed after payment, so check it carefully before completing the order.
Collections
Collection is available 7 days a week until 8pm by prior appointment, including bank holidays where agreed in advance. Arrange through eBay Messages before travelling.
VAT margin scheme
Sold under the applicable VAT margin/global accounting scheme. No separately reclaimable VAT is shown on the invoice.
How to find us / WhatsApp
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
Returns & Fitment Responsibility
Please use the part number, photographs, connector, mounting and hose layout to confirm suitability before purchase. We can assist with fitment checks through eBay Messages, but the buyer remains responsible for supplying accurate vehicle details.
Returns are handled in line with the return terms shown on the listing, eBay policy and applicable UK consumer law. Any refund deduction is considered only where an item is returned in a different condition and eBay permits a deduction for the actual loss in value.
ThePartPilot Stock, Workshop & Secure Dispatch
📦 25,000+ stocked parts
A large on-shelf inventory helps us supply replacement components quickly. Stock changes daily.
🔧 Workshop support
Fitting and repair work may be available subject to technician and ramp availability. Arrange through eBay Messages.
🛡️ Careful packing
Used components are checked against the order, protected and boxed for dispatch to reduce transit movement.
🌍 International fulfilment
Eligible overseas orders travel through eBay's managed international shipping process.