Nissan Note E11 2006-2013 Heater Blower Resistor CR14DE 1.4
Nissan Note E11 2006-2013 Heater Blower Resistor CR14DE 1.4
Critical Fitment Check Before You Buy
Do not rely solely on the title, a suggested part number or an automated vehicle-compatibility dropdown.
Before purchasing, compare your existing component against every high-resolution photograph in this listing. Check the electrical connector shape, connector keying, mounting ears, metal resistor body, dimensions, orientation and every stamped, moulded or handwritten marking.
The actual component pictured is handwritten MICRA 2006 and the connector housing carries visible identification including IN JAPAN, XEL and 1000-type moulded markings. No reliable Nissan service part number is clearly readable in the supplied photographs, so no unverified service number has been inserted into this description.
Actual Item - Photo Verification
Schematic reference only. Exact access position and trim removal vary by vehicle configuration.
Verified Item Details
Confirmed Source Compatibility
The source listing's configured vehicle compatibility identifies the following Nissan Note E11 / NE11 applications. Buyers must still compare the physical item with the part removed from their own vehicle before ordering.
| Year | Model | Chassis | Variant | Engine |
|---|---|---|---|---|
| 2006 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
| 2007 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
| 2008 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
| 2009 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
| 2010 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
| 2011 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
| 2012 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
| 2013 | Nissan Note | E11 / NE11 | Petrol MPV / 1.4 LPG | CR14DE - 1386cc - 65kW / 88HP |
Nissan Note E11 Vehicle Reference
Will Not Fit / Do Not Assume Compatibility
- Nissan Note E12 or later generations unless separately confirmed from the removed component and vehicle data.
- Nissan Micra K13 or later generations simply because the photographed part carries a MICRA donor note.
- Any vehicle using a different connector key, mounting flange, resistor body or mounting-hole pattern.
- Automatic or digital climate-control configurations that use a different electronic blower regulator or control module.
- Any engine, chassis or HVAC variant outside the configured compatibility table unless independently verified.
- Any vehicle where your removed resistor does not physically match the high-resolution photographs.
What This Component Does
This electrical resistor assembly forms part of the cabin heater, ventilation and air-conditioning blower circuit. Its job is to provide stepped electrical resistance so the cabin blower motor can operate at selectable fan speeds on compatible systems.
The resistor assembly is positioned in the HVAC airflow path so moving air can assist with managing the heat generated by the resistive elements. It does not itself create cabin heat or refrigeration and it is not the complete blower motor.
Typical Fault Symptoms
- One or more lower blower speeds stop working.
- The cabin fan operates only at a high-speed setting.
- Intermittent blower-speed operation.
- Loss of normal heater, demist or air-conditioning airflow despite other controls operating.
A resistor failure can also be secondary to another fault. Inspect the connector for heat damage and check the blower motor, wiring, cabin airflow and filter condition where applicable before treating the resistor as the sole cause.
Factory-Fit Recycled Component Value
Correct Physical Geometry Matters
A factory-fit component was designed around the vehicle's original connector, mounting points, HVAC casing and airflow environment. Physical matching is especially valuable on electrical components where similar-looking alternatives can have different connector keying or control characteristics.
Exceptional Recycled-Part Value
Selected recycled automotive components can save buyers up to 70 percent compared with purchasing new alternatives. The actual saving varies by part, availability and market price.
25,000 Plus Parts in Stock
THEPARTPILOT holds over 25,000 automotive parts in stock on the shelves, supporting fast identification and access to difficult-to-source replacement components.
Parts Storage and Stock Handling
Fitting Guide
Suggested Tools
- Plastic interior trim-removal tool.
- Small socket and ratchet set.
- Phillips and flat screwdrivers.
- Torx bit set where required by the vehicle.
- Inspection torch or workshop light.
- Suitable battery-terminal tool if battery isolation is specified for your vehicle.
- Protective gloves.
General Replacement Procedure
- Before dismantling anything, compare the replacement component with your existing unit and photographs.
- Switch the ignition fully off, remove the key and follow the correct vehicle electrical-isolation procedure where required.
- Remove only the lower-dashboard or glovebox trim necessary to access the heater and blower housing.
- Locate the resistor assembly inserted into the HVAC airbox close to the blower circuit.
- Inspect the connector and wiring for signs of overheating, corrosion, melting or previous repair.
- Disconnect the electrical plug without pulling directly on the wiring.
- Remove the resistor mounting fasteners.
- Withdraw the resistor carefully from the airflow housing.
- Compare the removed component side-by-side with this replacement before installation.
- Fit the replacement in the same orientation, secure the mounting points and reconnect the plug.
- Test every cabin blower-speed position and verify heater, demist and ventilation airflow.
- Once operation is confirmed, refit all removed trim securely.
Estimated planning time: approximately 0.5 labour hour / around 20 to 45 minutes. This is an estimate rather than manufacturer book time; access difficulty, trim layout and diagnostic work can increase the total.
Estimated Garage Labour Matrix
| Estimated Labour | £40 / hr | £60 / hr | £80 / hr | £100 / hr |
|---|---|---|---|---|
| 0.5 Hour | £20 | £30 | £40 | £50 |
Labour illustration only. It excludes diagnosis, additional damaged wiring, seized fasteners, additional components and local taxes or workshop charges.
Professional fitting service: fitting may also be available directly at our repair facility, subject to availability. Please use eBay Messages before purchasing to confirm vehicle details, fitting availability and appointment requirements.
Professional Workshop Support
Shipping and Delivery
UK delivery: buyers pay the calculated shipping charge shown by eBay at checkout. This description does not advertise free postage.
International delivery: eligible international orders may be handled through the eBay international-delivery programme displayed at checkout. Coverage can include eligible destinations across Europe, the USA, Canada, Australia and many other markets. Availability, international postage, import costs and destination eligibility are determined by eBay for the specific order.
VAT Margin Scheme Information
Where this component qualifies and is sold under our applicable Global Accounting VAT Margin Scheme for second-hand goods, VAT is accounted for within the margin and is not shown separately on the invoice. There is therefore no separately stated VAT amount available for the buyer to reclaim.
Returns and Buyer Verification
Please use the photographs and physical identifiers to confirm the correct component before installation. Ordering solely from an automated fitment dropdown without checking your old component can result in a physically incompatible resistor.
Returns are handled under the listing's eBay return settings and applicable statutory rights. No automatic restocking deduction is applied merely because a buyer changes their mind or ordered an incorrect variant.
Where eBay rules and applicable law permit, a deduction may be made for actual loss in value where a returned component is in a different condition because it has been installed, used, altered, damaged, returned incomplete or handled beyond what is reasonably necessary to inspect it. Eligible sellers may be able to deduct up to 50 percent where the proven loss in value justifies that amount.
Secure Dispatch Preparation
How to Find Us / Customer Support
Please use eBay Messages for pre-sale fitment questions and post-sale support. Our complete registered business contact information is displayed by eBay in the Business Seller Information or Business Details section where applicable.
For the quickest fitment check, send the vehicle registration or VIN where appropriate, together with clear photographs of your existing resistor, electrical connector and any stamped or moulded identification.
WhatsApp QR for Fitment Help / Appointment Enquiries
Scan the QR code to contact ThePartPilot on WhatsApp for fitment checks, appointments or fitting service availability.For faster fitment help, send your vehicle registration, VIN if available, and clear photos of your existing part, connector and part number.
Choosing a serviceable recycled automotive component helps keep high-grade materials in productive use, reduces unnecessary manufacturing demand and gives carefully recovered vehicle parts a valuable second working life.
Every sensible reuse decision can help reduce material waste while supporting a specialist UK automotive small business. Thank you for choosing to repair, reuse and keep vehicles on the road for longer.
Recycle. Reuse. Repair. Drive On.