Nissan Qashqai J11 MK2 2014-2021 OSR Right Rear Seat Belt Retractor 307735299
Nissan Qashqai J11 MK2 2014-2021 OSR Right Rear Seat Belt Retractor 307735299
Carefully identified used vehicle components, photographed individually and described to help you order the correct part the first time.
Nissan Qashqai J11 MK2 2014-2021 OSR Right Rear Seat Belt Retractor
Listing reference: 307735299 | Position: Right rear outer / RH rear / UK OSR
Actual Item Photographs
Vehicle Reference
Correct vehicle generation
This listing is for the second-generation Nissan Qashqai J11 five-door SUV. The photograph shows a facelift J11 vehicle within the stated compatibility period.
Important for 2021 vehicles: both J11 run-out vehicles and the newer J12 generation may be registered during 2021. Confirm the chassis generation is J11. Registration year alone is not sufficient.
Vehicle reference photo credit: Vauxford / Wikimedia Commons, CC BY-SA 4.0. Reference vehicle only.
Where This Part Is Fitted
THIS PART
International position: right-hand rear outer
The retractor is mounted behind the right-hand rear quarter/C-pillar interior trim, adjacent to the rear passenger seating area.
It stores and retracts the right rear outer seat-belt webbing, allows controlled occupant movement and mechanically locks the belt during abrupt vehicle movement or rapid belt extraction.
Part Specification
Confirmed Compatibility Chart
| Vehicle | Model year | Body / generation | Position | Fitment status |
|---|---|---|---|---|
| Nissan Qashqai | 2014 | J11 five-door | RH rear outer | Photo and label match required |
| Nissan Qashqai | 2015 | J11 five-door | RH rear outer | Photo and label match required |
| Nissan Qashqai | 2016 | J11 five-door | RH rear outer | Photo and label match required |
| Nissan Qashqai | 2017 | J11 five-door | RH rear outer | Check pre-facelift/facelift unit carefully |
| Nissan Qashqai | 2018 | J11 five-door | RH rear outer | Photo and label match required |
| Nissan Qashqai | 2019 | J11 five-door | RH rear outer | Strongest match to photographed date marking |
| Nissan Qashqai | 2020 | J11 five-door | RH rear outer | Photo and label match required |
| Nissan Qashqai | 2021 | J11 run-out five-door only | RH rear outer | Must be J11 – will not fit J12 |
Will Not Fit
| Vehicle or position | Reason | Status |
|---|---|---|
| Qashqai J10, approximately 2007-2013 | Earlier vehicle generation and different installation | Will not fit |
| Qashqai+2 J10 seven-seat model | Different body and rear occupant-restraint arrangement | Will not fit |
| Qashqai J12, 2021 onward | Replacement vehicle generation | Will not fit |
| Left rear outer / UK NSR | Opposite reel and bracket orientation | Will not fit |
| Rear centre position | Different mounting and belt arrangement | Will not fit |
| Front driver or front passenger position | Different assembly, mounting and safety-system configuration | Will not fit |
| Nissan X-Trail, Rogue or Rogue Sport | No exact interchange has been confirmed for this photographed unit | Not listed as compatible |
Seven-Point Fitment Check
- Confirm your vehicle chassis generation is J11.
- Confirm the vehicle is the five-door Qashqai.
- Confirm the required position is right rear outer.
- Compare the complete identification label with the listing photograph.
- Compare the number and shape of every mounting bracket and locating tab.
- Compare the webbing colour, buckle tongue style and reel orientation.
- When uncertain, send your VIN and clear photographs of the original unit through eBay Messages before purchase.
Possible Symptoms of a Faulty Retractor
- Belt webbing retracts slowly or remains loose after use.
- Belt remains jammed in the extended or retracted position.
- Retractor fails to lock when the belt is pulled sharply.
- Webbing is cut, frayed, glazed, contaminated or excessively twisted.
- Reel makes abnormal scraping, clicking or spring noises.
- Housing, mounting bracket or anchor shows collision damage or deformation.
- Belt does not sit correctly across the rear passenger.
Why Choose a Correct Factory-Fit Used Part?
- Correct mounting geometry and reel orientation when the exact application is matched.
- Correct belt length, routing and trim clearance for the intended vehicle position.
- No adaptation of mounting holes or brackets should be required.
- Original vehicle-quality materials and appearance help maintain a consistent interior finish.
- A quality used component may cost substantially less than a new dealer-supplied replacement.
Installation Overview
Recommended tools
- Plastic interior trim-removal tools
- Trim-clip pliers where required
- Ratchet and the correctly fitting socket for the vehicle fasteners
- Calibrated torque wrench capable of at least 49 Nm
- Protective trim tape and clean gloves
- Inspection lamp
General fitting procedure
- Switch off the ignition, keep the key away from the vehicle, disconnect the battery and wait at least three minutes before working around restraint-system components.
- Protect adjacent trim and record the original belt routing and mounting orientation.
- Remove the relevant rear pillar/quarter interior trim.
- Remove or release the rear seat cushion as required for access.
- Remove the right rear outer lower seat-belt anchor bolt.
- Support the assembly and remove the retractor mounting bolt.
- Install the replacement in exactly the same upright orientation, ensuring the webbing is not twisted.
- Tighten the retractor and outer anchor fasteners to the applicable manufacturer specification. The J11 service information specifies 49 Nm for the illustrated mounting points.
- Refit the seat cushion and trim without trapping the webbing.
- Confirm smooth extraction, complete retraction, free anchor movement and positive locking during a sharp pull test.
Instructions are a general overview and do not replace the complete workshop manual for the exact vehicle specification.
Estimated Repair Time and Labour Cost
Typical estimated fitting time is approximately 0.5 to 1.0 labour hour for a professional with suitable tools. Seized fasteners, damaged clips, previous repairs or additional diagnostic work can increase the time.
Garage labour estimate = hourly labour rate multiplied by billed hours. This table contains no JavaScript and is safe for an eBay description.
| Garage rate | 0.5 hour | 0.75 hour | 1.0 hour |
|---|---|---|---|
| £50 per hour | £25.00 | £37.50 | £50.00 |
| £70 per hour | £35.00 | £52.50 | £70.00 |
| £90 per hour | £45.00 | £67.50 | £90.00 |
| £120 per hour | £60.00 | £90.00 | £120.00 |
Illustrative labour only. Parts, diagnosis, VAT charged by an independent garage and additional repairs are not included.
Fitting, Repair and Collection Services
Collection appointments may also be available on bank holidays when agreed in advance. Contact us through eBay Messages before travelling to confirm availability, collection instructions and fitting options.
More Than 25,000 Parts in Stock
Delivery and Checkout Information
- UK delivery is provided using the service displayed in the listing.
- International delivery is available through eBay's eligible international shipping programme where offered at checkout.
- Destination availability, delivery charges, import charges and restricted locations are determined by eBay for each transaction.
- The delivery address selected at checkout must be complete and correct. For transaction security, we cannot redirect an order or replace the checkout address after payment.
- Any taxes, duties or import charges collected by eBay or customs will be displayed or administered separately where applicable.
How to find us / WhatsApp
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
Returns and Buyer Protection
Returns are handled in accordance with the return settings shown in the listing, eBay policy and applicable consumer rights.
- Please complete the fitment checks before installation.
- Returned components should be packaged securely and remain in the condition in which they were supplied.
- Any permitted deduction for diminished value can apply only where allowed by eBay policy and applicable law.
- Faulty, damaged, incorrect or materially not-as-described claims are handled through the applicable eBay buyer-protection process.
- Installation labour, diagnostic charges and consequential workshop costs are not included unless legally required.
Supporting Reuse and a Local Small Business
♻ Reuse before replacement: purchasing a suitable recycled vehicle component helps extend the useful life of an existing part and can reduce demand for additional manufacturing, packaging and raw materials.
📦 Carefully prepared: your order supports the work involved in vehicle dismantling, identification, photography, storage, customer support and dispatch.
🔧 Small-business support: every purchase helps an independent automotive recycling and parts business continue supplying cost-effective alternatives to new components.