Toyota Aygo MK1 5DR 2012-2014 OSR Right Rear Interior Door Handle 69205-0D060
Toyota Aygo MK1 5DR 2012-2014 OSR Right Rear Interior Door Handle 69205-0D060
Toyota Aygo MK1 5DR 2012-2014 OSR Right Rear Interior Door Handle
Dark-grey right-hand interior release handle • Used manufacturer-original part • Actual item photographed
Exact-fitment gate — designed to prevent wrong orders
Do not order by registration year alone. The photographed handle is dark grey and carries a donor-yard marking for a 2012 Aygo. Toyota catalogue data separates the earlier medium-grey handle from the later dark-grey handle. The safest advertised fitment is therefore Toyota Aygo MK1 KGB10 5-door, right-hand rear door, production 02/2012 to 05/2014. Before buying, compare the colour, lever shape, rear casing, fixing point and rod/cable connection with your removed part.
Part-number status: catalogue family 69205-0D060. The later dark-grey catalogue suffix is 69205-0D060-B3, but the full suffix is not readable in the listing photographs. For the highest-confidence check, send the vehicle VIN or registration plus clear front-and-rear photos of the old handle through eBay Messages before ordering.
Item photographs — use these before the eBay compatibility selector
Where this part is fitted
Right-hand rear interior handle
Mounted in the rear-right door trim and connected to the door-latch release linkage.
Highlighted area: OSR / right-hand rear door. On a UK right-hand-drive Aygo this is the driver's-side rear door; on a left-hand-drive car it is the passenger-side rear door.
Confirmed catalogue application and exclusions
| Vehicle | Production period | Body / position | Colour / reference | Decision |
|---|---|---|---|---|
|
Toyota Aygo MK1 AB10 / KGB10, 1.0 1KR-FE |
02/2012-05/2014 | 5-door hatchback Rear right / OSR |
Dark grey Catalogue candidate 69205-0D060-B3 |
PRIMARY FIT Confirm by photo and number where visible. |
| Toyota Aygo MK1 AB10 / KGB10 |
02/2012-05/2014 | 3-door or 5-door Front right interior position |
The same B3 catalogue reference appears in right-front diagrams. | CONDITIONAL Only after exact number, casing and linkage match. This listing is sold as rear right. |
| Toyota Aygo MK1 KGB10 / WNB10 |
02/2005-02/2012 | Right-hand interior handle positions shown by catalogue | Earlier medium-grey suffix 69205-0D060-B2 | NOT AN EXACT COLOUR MATCH Do not rely on year alone. |
| Toyota Aygo MK1 | Any year | Rear door on a 3-door car | No rear side door exists | WILL NOT FIT |
| Toyota Aygo MK2 / AB40 | From 05/2014 onward | Any door | Different generation and handle family | WILL NOT FIT |
| Toyota Aygo MK1 | Any year | Left-hand rear or left-hand front | Left-side family starts 69206, not 69205 | WILL NOT FIT |
| Citroën C1 / Peugeot 107 | Any year | Any position | No cross-brand reference has been physically verified on this item | NOT ADVERTISED AS COMPATIBLE |
Important: eBay's generic vehicle table can include engines or variants without proving door count, trim colour or production month. Use the photographs and chart above as the controlling fitment information. A VIN check remains the best method where any detail differs.
Catalogue and comparison references
Right-hand family
- 69205-0D060 — catalogue family / comparison reference.
- 69205-0D060-B3 — dark-grey catalogue application, 02/2012-05/2014.
- 69205-0D060-B2 — earlier medium-grey application, 02/2005-02/2012; not an exact colour match to the photographed item.
Numbers that are not this item
- 69206-0D060-B3 — corresponding dark-grey left-hand handle.
- 69206-0D060-B2 — corresponding earlier medium-grey left-hand handle.
- 90541-04027 — associated handle cushion reference; no separate loose cushion is promised unless shown in the item photographs.
What the handle controls and why replacement matters
Function
Pulling the inner lever transfers movement through the door's rod/cable and remote-control linkage to the latch, allowing the rear door to open from inside when unlocked and when the child lock is not engaged.
Construction
Textured injection-moulded automotive plastic housing and lever with a metal pivot/return-spring mechanism. Exact polymer grade is not claimed because the moulded material code is not readable in the photos.
Why use a factory part
Factory geometry helps preserve the correct fixing alignment, lever travel, linkage engagement, texture and trim colour. Cheap pattern copies can vary in pivot feel, spring tension, fit and finish.
Symptoms a failing inner handle may cause
- Lever feels loose, floppy or has excessive free play.
- Cracked lever, pivot boss or rear housing.
- Door will not release from inside although the outside handle works.
- Handle sticks, does not return cleanly or makes a clicking/rattling noise.
- Rod/cable end will not remain secured in the handle connection.
Check before replacing
A non-opening rear door is not always caused by the handle. First confirm the child-safety lock is off, the central locking is releasing, the linkage/cable is connected and the latch itself is free. Replace the handle only when the lever or its connection is damaged or worn.
Safety note: test all door functions with the door open before final reassembly.
Typical installation procedure
Guidance only: trim fasteners and tool sizes can differ by production date or previous repairs. Use vehicle-specific workshop information and stop if the door contains wiring, a side-airbag component or damaged fixings you are not qualified to handle.
Prepare safely
Park securely, remove the key and lower the window where possible. Protect painted and trim surfaces. If wiring must be disconnected, follow the vehicle procedure for battery isolation and radio/security settings.
Remove trim fixings
Remove visible screw covers, screws and the window-winder clip if fitted. Use plastic trim tools to release the door-card clips without twisting the panel.
Lift off the door card
Lift the panel upward from the window ledge. Disconnect any switch plug and support the panel so its wiring is not strained.
Release the old handle
Remove the handle fixing, then carefully unclip the rod or cable end. Note its routing and clip orientation before removal.
Compare before fitting
Place old and replacement parts side by side. Confirm right-hand orientation, colour, lever profile, mounting point, rear casing and linkage slot are identical.
Install and test
Connect the linkage securely and fasten the handle. With the door open, test inner release, outer release, lock/unlock and child-lock operation several times.
Reassemble
Reconnect switches, replace any broken trim clips, engage the upper door-card edge and press clips home evenly. Refit screws and covers without overtightening plastic parts.
Required tools, estimated time and garage-cost guide
Typical tools
- Plastic trim-removal tools
- Phillips and vehicle-matched Torx/hex drivers
- Small pick or hook tool
- Trim-clip pliers
- Window-winder clip tool where applicable
- Torch, gloves and protective tape
- 10 mm spanner only if battery isolation is required
Static labour calculator
Because eBay descriptions cannot use active calculators, use the table below.
Example: £90/hour × 0.75 hour = £67.50 labour.
| Garage hourly rate | 0.50 hour estimate | 0.75 hour estimate |
|---|---|---|
| £50/hour | £25.00 | £37.50 |
| £60/hour | £30.00 | £45.00 |
| £75/hour | £37.50 | £56.25 |
| £90/hour | £45.00 | £67.50 |
| £100/hour | £50.00 | £75.00 |
| £120/hour | £60.00 | £90.00 |
| £150/hour | £75.00 | £112.50 |
Estimates are labour only and exclude diagnosis, VAT charged by the repairer, clips, consumables, travel and additional faults. Actual time and rate vary by garage and vehicle condition.
Fitting service available subject to capacity
Arrange through eBay
Fitting is subject to technician availability, prior diagnosis and a separately agreed quotation. Message us through eBay before purchase with the registration or VIN, the listing number and photos of the existing part.
Do not travel without confirmation. Collection and fitting appointments are not guaranteed until agreed in eBay Messages.
25,000+ parts held in stock and on the shelf
Image transparency: the workshop and warehouse photographs in these reference panels are licensed illustrative stock images and are not photographs of ThePartPilot premises. The six product photographs above show the actual item offered in this listing.
Important order information
Collection
Collection may be arranged by prior appointment seven days a week up to 8 pm, including bank holidays, subject to confirmation. Arrange the time through eBay Messages before travelling.
International delivery
International orders are available where this item and the buyer's destination are accepted by eBay International Shipping. Eligible countries, delivery charges, import taxes and duties are calculated dynamically by eBay at checkout, so a fixed country list is not stated here.
Checkout address
Please check the delivery address before payment. We cannot manually redirect an order to a different address after checkout. Where eBay permits, an incorrect-address order may need to be cancelled and purchased again.
VAT treatment
Sold under the Global Accounting VAT margin scheme where applicable. VAT is accounted for within the scheme and is not shown separately. A recoverable-VAT invoice is not supplied for a margin-scheme sale.
How to find us / WhatsApp
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
Help us get the correct part to you first time
Before purchase
- Confirm MK1 / AB10 / KGB10 generation.
- Confirm 5-door body for a rear-door installation.
- Confirm right-hand / OSR position.
- Confirm dark-grey colour and 02/2012-05/2014 production period.
- Compare the actual item photos with the removed handle.
- Request a VIN/photo check through eBay Messages if uncertain.
Formal return terms
The controlling return period, postage responsibility and refund terms are the return settings shown by eBay on this listing and applicable consumer law. There is no automatic restocking or administration charge. Please avoid fitting, altering or damaging the item until fitment has been checked against the photos and reference information.
Correct fit, lower cost and less waste
Better geometry
Factory mounting points and linkage travel are designed around the original door system, helping avoid the poor alignment that can occur with low-cost pattern copies.
Potential saving
Buying a tested used part can save as much as 70% against the price of a comparable new part in some cases. Actual savings vary by reference, availability and new retail price.
Reuse first
Reusing a serviceable component extends its useful life and reduces demand for new raw material, manufacturing energy and avoidable waste.
Thank you for supporting a local small business
Every correctly matched recycled part supports skilled local employment and keeps a usable component in service. Choosing a quality used part can reduce cost, cut waste and help make vehicle repair more sustainable. We appreciate every order and aim to provide the detail needed for you to buy correctly the first time.