Vauxhall Astra H A04 1.7 CDTi 2004-2010 Brake Pedal Box 13178200
Vauxhall Astra H A04 1.7 CDTi 2004-2010 Brake Pedal Box 13178200
VAUXHALL ASTRA H A04 1.7 CDTi 2004-2010 04-10 MANUAL BRAKE PEDAL BOX ASSEMBLY
Carefully selected pre-owned factory-fit automotive component, professionally handled and supplied exactly as pictured.
Brake Pedal Box / Mounting Assembly
This listing is for the pictured Vauxhall Astra H brake pedal box assembly for a manual-transmission 1.7 CDTi application within the 2004-2010 (04-10) source fitment bracket.
The Component You Are Buying
These images show the actual style and configuration of the listed assembly. Please use them as your primary visual reference.
Exact Donor Vehicle Image
A Serious Automotive Parts Operation
With more than 25,000 automotive components held on our shelves, THEPARTPILOT is built around fast identification, careful stock control and helping buyers locate the correct replacement component.
Why a Factory-Fit Component Can Be the Smarter Choice
A brake pedal assembly is a structural control component. Correct pedal ratio, mounting geometry, pivot alignment, bracket rigidity and switch activation position all matter. A properly matched factory-fit component was designed around the vehicle's original mounting points and operating geometry.
Correct Geometry
Maintains the intended pedal position, travel and relationship with the brake-servo pushrod.Structural Rigidity
Correct bracket shape and material thickness help minimise unwanted flex during braking input.Switch Alignment
Correct mounting geometry is important for consistent activation of the brake / stop-lamp pedal switch.Mounting Accuracy
Factory-positioned fixing points reduce the risk created by poorly aligned substitute components.Better Value
A carefully selected recycled factory-fit component can provide substantial savings compared with purchasing a new equivalent.Less Waste
Reusing a serviceable structural assembly keeps valuable steel, rubber and plastic components in circulation.Brake Pedal Assembly Function
The pedal lever receives the driver's foot input and mechanically transfers that movement through its pivot and connection point towards the brake-servo / booster pushrod. The rigid mounting structure holds the pedal in its designed position relative to the bulkhead and surrounding controls.
The pictured assembly also carries an electrical pedal switch. Depending on the vehicle specification, brake-pedal switch signals are used for stop-lamp operation and may also be referenced by related vehicle control functions.
Compatibility — Verify Before Purchase
| Make / Model | Platform | Engine | Transmission | Years | Verification |
|---|---|---|---|---|---|
| Vauxhall Astra H / Mk5 | A04 | 1.7 CDTi | Manual | 2004-2010 04-10 |
Match physical bracket, pedal, switch, steering side and identification markings before purchase. |
Will Not Fit / Do Not Assume Compatibility
Similar-looking parts can have different mounting geometry, identification codes, switch arrangements or steering-side configurations. Matching the actual component is the safest way to prevent ordering the wrong variant.
Where the Assembly Mounts
The assembly is located in the front footwell and is mechanically secured to the vehicle's pedal-support / crossmember and bulkhead area, with the pedal connected to the braking input mechanism.
Professional Fitting Guide
Typical Tools Required
Typical Installation Sequence
- Confirm the replacement assembly is the correct physical and identification match before dismantling the vehicle.
- Park securely, keep the wheels straight, isolate the ignition and disconnect the battery in accordance with workshop procedures.
- Remove the necessary lower dashboard, steering-column and footwell trim to obtain safe access to the pedal mounting structure.
- Where required by the exact procedure, release steering-shaft components only after marking their original alignment and following the manufacturer's safety instructions.
- Disconnect the brake-pedal / stop-lamp switch electrical connector.
- Release the pedal return spring and the brake-servo / pushrod connection using the correct clip / retaining procedure.
- Support the assembly and remove its mounting fasteners in the specified sequence.
- Compare old and replacement parts side-by-side: brackets, pivots, pedal angle, pad, switch, mounting holes and identification marks must correspond.
- Install the replacement assembly and refit all fasteners, clips, locking devices and steering components to vehicle-specific specifications.
- Reconnect the electrical switch and ensure correct switch engagement through the full pedal travel.
- Reconnect the battery and verify brake-light operation, pedal return, pedal feel and all affected electrical functions.
- Complete a professional safety inspection before the vehicle is returned to road use.
Indicative workshop planning allowance: approximately 2.0 hours. This is not a manufacturer flat-rate time. Actual labour varies with vehicle specification, trim removal, access, corrosion and steering-shaft configuration.
Indicative Garage Labour Cost Matrix
| Planning Time | £40 / hr | £60 / hr | £80 / hr | £100 / hr |
|---|---|---|---|---|
| 2.0 Hours | £80 | £120 | £160 | £200 |
Labour figures are illustrative only and exclude additional parts, diagnostics, consumables, seized fasteners or other work discovered during installation.
Professional Mechanical Support
UK & International Delivery
UK Delivery
Shipping is charged according to the postage service and destination shown at eBay checkout. No free-postage promise is made in this description.International Delivery
Eligible international orders can be handled through eBay's Global Shipping Programme to supported destinations across Europe and markets including the USA, Canada and Australia.Carefully Prepared for Dispatch
Components are prepared for transport with the aim of protecting vulnerable mounting points, connectors and projecting sections during normal courier handling.
VAT, Returns & Warranty
VAT Margin Scheme
Sold under the VAT Global Accounting / Margin Scheme where applicable. VAT is not separately itemised and no reclaimable VAT invoice is available.30 Day Warranty
This component is supplied with the listing's stated 30-day seller warranty, subject to the applicable listing terms and eBay policy.Please verify fitment against the high-resolution photographs, physical mounting configuration and exact stamped / moulded reference information. Automated compatibility information is a useful aid, but should not replace physical part-number and component matching.
Need Help Matching the Part?
For the fastest fitment check, send us your vehicle registration or VIN information together with a clear photograph of your existing component and every visible identification marking through the communication options provided by eBay.
WhatsApp QR for Fitment Help / Appointment Enquiries
Scan the QR code to contact ThePartPilot on WhatsApp for fitment checks, appointments or fitting service availability.For faster fitment help, send your vehicle registration, VIN if available, and clear photos of your existing part, connector and part number.