Vauxhall Corsa D Rear Right Seat Belt Buckle Stalk 616609200A F13276908
Vauxhall Corsa D Rear Right Seat Belt Buckle Stalk 616609200A F13276908
REAR RIGHT / OFFSIDE SEAT BELT BUCKLE STALK
| Brand | Vauxhall |
| Vehicle family | Corsa D |
| Component | Rear seat belt buckle / stalk |
| Position | Rear Right / Offside |
| Stamped / reference number | 616609200A |
| Additional references | F13276908 / 40-126-6978 |
| Condition | Used |
Seat-belt components are safety-critical. Match the stamped/reference number 616609200A and the physical connector, mounting arrangement and buckle configuration shown in the listing photographs against your existing component. Do not order solely because your vehicle is described as a Corsa D.
Component Description
This listing is for a Vauxhall Corsa D rear right / offside seat-belt buckle stalk assembly, identified by reference 616609200A, with additional references F13276908 and 40-126-6978.
The buckle/stalk forms the receiving and latching point for the applicable rear seat-belt tongue. It is mounted within the rear seating area and forms part of the vehicle's occupant-restraint system.
Because seat-belt systems can vary by production specification, restraint layout, body configuration and component revision, the stamped number and physical design must be checked before purchase.
Mounting Position Reference
Technical illustration placeholder — replace with your own verified model-specific fitment image.
Compatibility & Verification
| Attribute | Listing Reference | Verification |
|---|---|---|
| Model family | Vauxhall Corsa D | Verify before purchase |
| Position | Rear Right / Offside | Match existing component |
| Reference | 616609200A | Exact number check strongly recommended |
| Advertised donor/application range | 2006–2015 | Not confirmation of every vehicle within this period |
IMPORTANT: A model/year range is not sufficient to establish safety-critical seat-belt fitment. Verify the component number and vehicle specification before ordering.
3-Door vs 5-Door — Check Your Vehicle
3-DOOR
|
5-DOOR
|
These illustrations are identification references only. Do not infer compatibility from body shape alone. Match your existing component number and configuration.
Will Not Fit / Exclusions
Do not purchase this component where:
- Your existing buckle carries a different incompatible part/reference number.
- The buckle shape or seat-belt tongue interface differs from the photographs.
- The mounting arrangement differs from the item shown.
- The electrical connector, where fitted, differs in shape, pin configuration or wiring.
- Your required position is not rear right / offside.
- Your vehicle specification cannot be positively matched to the supplied component.
Similar-looking restraint components are not automatically interchangeable. If uncertain, obtain VIN-specific parts information before ordering.
Why Choose an Original Factory Component?
A quality used factory-manufactured component retains the original vehicle manufacturer's intended dimensions, mounting geometry and application-specific design.
Cheap aftermarket copies may use different materials, tolerances or construction. For important vehicle components, buying the correct original factory part can provide excellent value while avoiding unnecessary compromise.
Professional Installation Recommended
This component forms part of the occupant-restraint system. Installation should be carried out by a competent automotive technician using the manufacturer's workshop procedure and specified fastener torque.
Typical Workshop Procedure
- Confirm the replacement component number and application before dismantling.
- Secure the vehicle and follow the manufacturer's restraint-system safety procedure.
- Move or remove the required rear-seat cushion/trim to expose the buckle mounting.
- Disconnect any applicable electrical connector only in accordance with workshop instructions.
- Remove the buckle/stalk mounting fastener using the appropriate tool.
- Compare the removed and replacement components before installation.
- Install the replacement buckle in its correct orientation.
- Tighten the restraint-system fastener to the manufacturer-specified torque.
- Reconnect applicable wiring and correctly refit all trim/seating components.
- Perform the prescribed restraint-system and buckle operation checks before vehicle use.
Typical Tools
Appropriate socket/bit set, ratchet, trim tools and a calibrated torque wrench. Exact tool sizes and torque specifications must be obtained from the correct VIN-specific workshop information.
Typical labour allowance: approximately 0.5–1.0 hour where no additional diagnosis or seized/damaged hardware is encountered. This is an estimate only.
Indicative Labour Cost Matrix
| Time | £40/hr | £60/hr | £80/hr | £100/hr |
|---|---|---|---|---|
| 0.5 hour | £20 | £30 | £40 | £50 |
| 1.0 hour | £40 | £60 | £80 | £100 |
Illustrative labour only. Diagnostic work, additional dismantling, damaged fasteners, consumables and local workshop rates may alter the final cost.
Professional fitting is also available directly through our repair facility, subject to workshop availability. Please use eBay Messages for enquiries.
Secure Shipping
Postage is not free. Buyers pay the calculated shipping charge displayed by eBay for their delivery destination and selected service.
Where available for the destination/listing, international orders are securely dispatched through eBay's international shipping facilities, serving destinations including the UK, Europe, USA, Australia, Canada and other supported regions. Availability and charges are those displayed by eBay at checkout.
Carefully Packed. Securely Dispatched.
Fitment & Returns
Buyers are strongly encouraged to verify compatibility using the high-resolution listing photographs, stamped/reference numbers and their vehicle-specific parts information rather than relying solely on automated compatibility dropdowns.
If a return is accepted, the item should be returned in the same condition in which it was supplied. Any permitted deduction for diminished value will only be applied where justified by the condition of the returned item and in accordance with applicable law and eBay's returns rules.
VAT Margin Scheme
Where this used component is sold under the applicable VAT Margin Scheme, VAT is not separately itemised or reclaimable by the purchaser.
How to Find Us / Customer Support
Scan the QR code to open a WhatsApp chat for collections and enquiries.
If the QR image needs refreshing, generate it again from the same WhatsApp link.
A Smarter Choice for Your Car & the Planet 🌍♻️
Choosing a quality recycled automotive component gives an existing high-grade part another useful life while helping reduce demand for new manufacturing, raw materials, energy consumption and unnecessary automotive waste. ♻️🚗
Every reused component helps move the automotive industry towards a more circular economy while supporting a growing UK small business. Thank you for choosing THEPARTPILOT. 💚🔧