VAUXHALL CORSA E MK4 2014-2019 LEFT REAR BUMPER BRACKET 39085591

VAUXHALL CORSA E MK4 2014-2019 LEFT REAR BUMPER BRACKET 39085591

£17.95
Skip to product information
VAUXHALL CORSA E MK4 2014-2019 LEFT REAR BUMPER BRACKET 39085591

VAUXHALL CORSA E MK4 2014-2019 LEFT REAR BUMPER BRACKET 39085591

£17.95
THEPARTPILOT
Premium Recycled Automotive Components
25,000+ PARTS ON THE SHELVES
30 DAY SELLER WARRANTY
SECURE PACKING
UK & INTERNATIONAL DELIVERY
Verified From Actual Item Photos

VAUXHALL CORSA E MK4 2014-2019
LEFT / NEARSIDE REAR BUMPER MOUNTING BRACKET
39085591

Vauxhall Corsa E Mk IV / X15 2014 - 2019 Left Rear Nearside Rear MPN 39085591

Actual Item — Buy What You See

These are photographs from this exact eBay item. Please inspect every image carefully before ordering.

Vauxhall Corsa E left rear bumper mounting bracket 39085591
Actual black moulded rear-left bumper support / guide supplied with this listing.
39085591 LH PP-GF20 part number marking
Critical identification image — check the moulded/stamped number against your existing component.
Corsa 2019 NSR identification marking
Item identification / breaker marking showing Corsa 2019 NSR.

Engineering Identification

Identification Point Verified Detail
Manufacturer Part Number 39085591
Handing Mark LH — Left Hand
Position Rear Left / UK Nearside Rear
Material Marking PP-GF20 — polypropylene reinforced with approximately 20% glass fibre
Additional Mould Reference 475 498 858
Visible Supplier / Production Marking AC GROUP
Colour / Finish Black self-coloured moulded plastic
eBay Item Number 147507396341

What This Component Does

This is the left rear bumper mounting bracket / guide. It sits between the rear bumper cover and the vehicle's left-rear body / quarter-panel mounting area.

Locates The Bumper Corner Helps hold the outer rear bumper cover in the correct position against the bodywork.
Maintains Panel Alignment Correct locating geometry helps maintain a consistent bumper-to-body panel gap.
Supports Retention Tabs Provides the moulded mounting and locating points used by the bumper corner assembly.
Important: This is a body mounting component. It does not control the engine, transmission, steering, braking or vehicle electronics.

Physical Mounting Location

🚗 REAR LEFT / NEARSIDE BUMPER CORNER

Mounted behind the left side of the rear bumper cover at the bumper-to-body / quarter-panel interface.

The "Front Transmission Bay" location used for gearbox components is not applicable to this part.

Vehicle Compatibility Guide

Fits: Vauxhall Corsa E 2014 - 2019 (14-19)
Match the chassis generation, left-rear position, physical shape and stamped 39085591 number before ordering.
Make Model / Generation Years Chassis Position
Vauxhall Corsa E / Mk IV 2014 - 2019
14-19
X15 Left Rear / Nearside Rear

Engine size, fuel type and gearbox are not the primary compatibility identifiers for this body mounting bracket. The safest match is vehicle generation + mounting side + exact part number + physical comparison with the photographs.

WILL NOT FIT / CHECK BEFORE PURCHASE

  • Vauxhall Corsa D / earlier generation bumper systems.
  • Vauxhall Corsa F / Mk V later-generation bumper systems.
  • Right-hand / offside rear mounting position.
  • Vehicles using a different bracket shape or stamped part number.
  • Any bumper conversion where mounting points have been modified.
  • Any vehicle where your existing bracket does not visually match the high-resolution photographs in this listing.

Critical Fitment Check — Please Do This First

Do not rely solely on automated compatibility menus.

Before purchasing, compare your original component with the photographs and verify the stamped/moulded number 39085591, the LH position marking, mounting hole pattern, locating rails, tabs and overall shape.

If your number or physical geometry differs, please send us an eBay Message with your vehicle details before ordering.

Why Choose A Factory-Fit Recycled Component?

Correct Moulding Geometry A factory-fit component was designed around the vehicle's original bumper mounting architecture, helping preserve correct alignment.
Known Material Specification This component carries a PP-GF20 moulding identification, providing a useful material reference when matching the replacement.
Reuse Instead Of Re-Manufacture Reusing a serviceable automotive component can reduce demand for new material, new manufacturing and unnecessary disposal.
Cost-Efficient Repair Recycled factory-fit components can offer substantial value compared with purchasing new parts, depending on current market pricing.
25,000+ PARTS IN STOCK ON THE SHELVES THEPARTPILOT — supporting repairs with quality recycled automotive components

Condition & What You Receive

This is a previously fitted automotive component. Normal cosmetic marks, storage marks, surface wear and evidence of prior installation may be present.

The photographs form an important part of the item description. You will receive the component shown. Please assume that ancillary fasteners, clips or additional trim are not included unless they are clearly visible in the photographs.

Fitting Guide

General guidance only. Exact fastener sequence can vary by bumper, trim level and previous repair history.

1. Confirm your replacement is stamped 39085591 / LH and visually matches the original.
2. Park safely, switch the ignition off and protect painted bumper/body surfaces.
3. Remove the necessary wheel-arch / bumper-corner fasteners and trim clips.
4. Where required, remove adjacent trim or lamp access components needed to reach concealed fasteners.
5. Carefully release the left-rear bumper corner without forcing or bending its locating tabs.
6. Remove the damaged bumper guide / mounting bracket and inspect the body mounting points.
7. Install the replacement bracket using serviceable clips / fasteners and align it before final tightening.
8. Engage the bumper-cover locating tabs into the guide progressively and check that they seat correctly.
9. Refit all removed fasteners and trim components.
10. Inspect bumper-to-quarter-panel alignment and confirm there are no loose corners or abnormal panel gaps.

Suggested Tools

  • Plastic trim-removal tools
  • Trim clip remover
  • Torx bit selection
  • Socket and ratchet set
  • Screwdriver set
  • Inspection lamp
  • Protective gloves
  • Soft blanket / panel protection
Indicative workshop time: approximately 0.5-1.0 labour hour for a straightforward installation. Seized fasteners, damaged bumper tabs, previous repairs or additional bumper removal work can increase this.

Static Garage Labour Cost Guide

Illustrative labour only. This table is hardcoded and contains no calculator, script or active content.

Illustrative Labour Time £40/hr £60/hr £80/hr £100/hr
0.5 hour £20 £30 £40 £50
1.0 hour £40 £60 £80 £100

Labour rates and billed time vary between repairers. Parts, clips, diagnostics and additional body repairs are not included.

Professional Fitting

Professional fitting may be available at our repair facility, subject to workshop availability. Please contact our team through eBay Messages before purchase to check whether a suitable eBay-compliant fitting arrangement is available.

Delivery & Worldwide Shipping

Postage is not offered as free within this description. Shipping charges applicable to your order are displayed or calculated by eBay at checkout according to destination and available delivery service.

Eligible international orders may be securely processed through the eBay Global Shipping Programme where the programme is displayed at checkout. Eligible destinations may include the UK, Europe, USA, Australia, Canada and other supported regions.

International availability, shipping charges, import costs and estimated delivery times are those displayed by eBay for the buyer's destination at checkout.

Important: Customers must ensure their checkout address is correct prior to paying. Due to strict eBay Seller Protection regulations, we are entirely unable to alter or change your delivery address after purchase.

Secure Warehouse Dispatch

Picked From Stock Item identity is checked against the order before packing.
Protected For Transit Components are packed to help protect mounting points and vulnerable edges during delivery.
Tracked Where Applicable Delivery information is provided through the eBay order system for the service selected.

VAT Margin Scheme Information

Where this used component is sold under the applicable Global Accounting VAT Margin Scheme, VAT is accounted for within the seller's margin and is not separately itemised on the sales invoice.

Accordingly, there is no separately stated VAT amount available for the buyer to reclaim on this item.

Returns & Buyer Fitment Responsibility

Please verify the part number, mounting side, shape, tabs and photographs before ordering. If you are uncertain, contact us through eBay Messages before purchase.

Change-of-mind and incorrectly ordered returns are handled in accordance with the return terms displayed by eBay for this listing and applicable consumer law.

Returned-condition protection: There is no automatic restocking penalty. Where an eligible return is received back used, altered, damaged, incomplete or otherwise in a materially different condition from that originally supplied, eBay may permit an appropriate refund deduction of up to 50% to reflect the actual loss in value, subject to eBay's rules and seller eligibility.

How to Find Us / Customer Support

WhatsApp QR for Fitment Help / Appointment Enquiries 

Scan the QR code to contact ThePartPilot on WhatsApp for fitment checks, appointments or fitting service availability.       
      
For faster fitment help, send your vehicle registration, VIN if available, and clear photos of your existing part, connector and part number.  

You may also like